Last updated 14 November 2026
Bulldog
A pictorial record of the restoration to flying condition of
Scottish Aviation Bulldog AS0023
Last updated 14 November 2026
A pictorial record of the restoration to flying condition of
Scottish Aviation Bulldog AS0023
AS0023 was delivered to the RAF as Bulldog T1 XX714 in 1976. The RAF ordered 130 Bulldogs which were delivered between 1973 and 1976. XX714 was the final aircraft and has construction number BH120/363. While most RAF Bulldogs entered standard training units straight away, XX714 was initially held back by Scottish Aviation and used as a specialized development, demonstration, and test aircraft. It was later allocated to the RAF Central Flying School where, rather than teaching raw cadet pilots, it was used by experienced pilots learning to become Qualified Flying Instructors.
XX714 at Prestwick Airport (the Scottish Aviation manufacturing site) in 1977
The Grob Tutor T1 began to replace the Bulldog T1 in RAF service in 1999. The transition took place gradually over a couple of years, with the RAF Bulldog fleet being fully retired and sold off to civilian owners by 2001. However, in 2000, following evaluations and discussions in previous years, the Armed Forces of Malta (AFM) took ownership of four of the best RAF Bulldogs before they were offered to the general public, XX714 being one of them. They were flown from RAF Newton to Malta in early 2000.
The four AFM Bulldogs arrive in Malta
AS0023 in service with the AFM Air Wing
After successfully serving for many years with the AFM Air Wing as a coastal patrol and training aircraft the Bulldog fleet was retired from active service in 2013. AS0023's final flight with the AMF – and indeed its last flight to date – was on 14th December 2011. Following their retirement, the disposal process concluded with one aircraft transferred to the Malta Aviation Museum, one donated to the Malta College of Arts, Science and Technology to serve as a hands-on instructional tool for aircraft engineering students, and two (including AS0023) being sold by tender and returned to the United Kingdom.
An excellent account of the story behind the Maltese Bulldogs can be found here: From Sky to Museum
Malta Government Gazette tender announcement
The proud new owner of AS0023 in the AFM hangar
After de-rigging the aircraft (i.e. detaching the wings, tailplane, and rudder) in the AFM hangar it was loaded onto a trailer for transportation to the UK.
Departing the AFM hangar enroute to the UK
The route was Malta - ferry - Sicily - ferry - Italy - tunnel - France - ferry - United Kingdom. The 3,044 km journey took five days, being extended by a cautious trailer towing speed, waiting for ferries, and a few sleeps! A Mondeo fully reclined driver's seat is surprisingly comfortable! (Not wanting to leave the trailer – and more importantly its load – unattended overnight.)
On the ferry in Messina
Entering the Fréjus Road Tunnel through the Alps between Italy and France
At Calais waiting to board the midnight ferry to the UK
Safely stored in the owner's garage-cum-hangar
The RAF Bulldogs are fitted with fatigue meters which constantly monitor and record the stresses imposed on the aircraft in flight. These stresses are much greater during aerobatics, for example, than in steady level flight. The meter readings are used to calculate the cumulative stresses over time, the result being an ever-increasing number known as the Fatigue Index (FI). Once this FI reaches 114 the aircraft is grounded and no longer permitted to fly. This terminal FI of 114 was arrived at by stressing a test airframe on the ground to structural failure and then applying a safety margin. Irrespective of the FI there is also an absolute limit of 15,000 accumulated flying hours before the aircraft must be permanently grounded.
It's worth noting that once the 114 FI limit has been reached a modification can be embodied to extend the FI limit to 200. However, this is very expensive (c.£45K) and modification kits are not currently available. It has been applied to five aircraft in the past. Most ex-RAF Bulldogs currently flying in the UK have accumulated around 9,000 flying hours and many have an FI of 110+.
Due to it having very low utilisation in its early years (it didn't reach 1,000 hours until 1992 - when it was 16 years old!) AS0023 has exceptionally low total flying hours for the type. For similar reasons, it has by far the lowest FI of all ex-RAF Bulldogs. The current figures are 4,724 total flying hours and 58 FI. Because these numbers are so low it is worth spending the time and money to restore it to a high standard, so it was decided to undertake a bare-metal repaint.
The only difference between the RAF and AFM livery is that the roundels and tail flash are replaced with the Maltese versions. The original RAF paint scheme is well documented.
Unloading the fuselage at the paintshop, the wings, etc., having been delivered earlier
Stripping the wings - very labour intensive
Before paint stripping is started all the holes – large and small – need to be masked or blocked to prevent the chemicals finding their way into unwanted places. Once the paint has been completely stripped the surfaces are thoroughly cleaned to remove all traces of chemicals. Etch primer is then applied, green in colour. At this stage it is easy to see all the minor imperfections, mainly small “dings”. These are small enough to remediate with filler. Larger dents would need a repair scheme to be developed, usually involving a patch or replacement skin panel. Fortunately AS0023 only had minor blemishes so filler sufficed.
Wing in primer and small dings being filled
Once all the imperfections have been removed a white primer/undercoat is applied to the wings. This is required to bring out the vibrancy of the final colours, particularly to ensure the red colour meets strict British Standard specifications. This colour (BS 381C 537 Signal Red) is calibrated over a bright, neutral-white base. Applying it over standard green aviation epoxy primers would turn the red muddy, dark, or brownish.
Blemish-free wings in white primer/undercoat ready for the topcoat
Wings in the paint booth, with a few smaller parts
The red outer section of the wings finished, waiting for grey on the inner sections
As well as the main structures there are many smaller parts that go through the same strip-prime-fill-undercoat-paint process. Some budget aircraft repaints leave access panels, etc., in situ, but preparing and painting them separately is a better way to do it. The Bulldog has four fuel tanks incorporated in the bottom surface of the wings. The visible surface of these tanks is painted to the same standard as the rest of the wings.
Green etch primer time in the spray booth
Fuel tanks in etch primer and various finished access panels, etc.
Sliding canopy completely finished in white
Partly finished upper and lower engine cowlings
With the canopy removed and all apertures masked off stripping of the fuselage begins. Because of the area involved the paint stripper is sprayed on rather than being applied by brush.
The next day the paint is literally dripping off
Paint nearly all gone - a real mess!
Interesting to see traces of the original RAF "XX714"
Back to bare metal except for a few fibreglass parts
Freshly applied green etch primer
First coat of red after the white primer/undercoat
Red and white finished, ready for grey on the stub wings
Stub wings now grey and fibreglass deflector strakes red